DATRON 4700 PDF

  • May 23, 2019

Model Specifications. Manufacturer(s). Datron. Instrument Model: Description: Autocal Multifunction Calibrator. Instrument Type(s). Calibrator. Application. Find great deals for DATRON AUTOCAL Multifunction Calibrator as Is. Shop with confidence on eBay!. Datron | Sale | Rental | Lease – Calibrator. Datron Calibrator. Contact us for pricing and availability. Description; Options.

Author: Malahn Kajizshura
Country: Bulgaria
Language: English (Spanish)
Genre: Career
Published (Last): 5 January 2008
Pages: 267
PDF File Size: 11.31 Mb
ePub File Size: 19.28 Mb
ISBN: 853-8-20340-460-6
Downloads: 34696
Price: Free* [*Free Regsitration Required]
Uploader: Zulkijind

Full details of the operation Of Specification mode are given in Section 4. Set the DC Cmrent Sta. Carry out the DC Voltage performance checks I.

Wavetek/Datron 4708, 4707, and 4705 Multi-Product Calibrators

Use Calculation B if the was last calibrated again. Spaces are provided to datton tiie displayed limits as well as the measured values. The appropriate limit calculations are detailed in Appendix 4. Standard accessories supplied with the instrument are as described in Section 1.

[volt-nuts] Datron 4700 manual and options

The load resistance is low enough to cause a significant voltage drop in the output Connection- Sensitive measurements are being made. The ratio ; Total Lead Resistance Load Resistance gives the approximate error for 2-wire connection at low frequencies. The abbreviations used for these calculations are: The output of the is fully floating, so its output may be refeiTcd to dagron common mode voltage within the range specifiedonpage 6. Stepping from 0 to 9 decreases the value by 1.

  KIDANJE VEZA PHYLLIS KRYSTAL PDF

The controller would perform other tasks during this period. On n ranges, only the overrange f f are operative.

Set to IV Range, ikflz, and adjust for corrected 1. Over-Voltage Checks The automatically tests the over-voltage detector threshold levels in Low Voltage state. The I-command and the WI command must not be sent in the same siring. Referto Section 4 page Autoranging Stepping the frequency beyond the span of a range automatically switches range up or down, but ftirilier steps are inhibited until the A or f key is released the datrn could be below a decimal point.

Resolution and Accuracy The maximum resolution is digits with a unique facility for displaying the specified accuracy of output current. The Resistance value displayed is the calibrated value of the standard interaai resistor selected not the nominal value.

SET can also be used as a means of compensating for known errors in the Measurement System.

Datron Instruments (FLUKE) equipment for sale at Used-Line

Ensure that the is set to ratron 1 00m V AC range. Twist or run leads togetlieikeep length less than I meter. Ensure that the DVM is still comiected to the terminals as shown in Fig.

  LUXACION DE HOMBRO PDF

General View dattron Datron Auloca Multifunction Calibrator Introduction Tlie Datron Autocal Multifunction, Calibrator is a high-precision calibrator which features exceptionally higli stability and full systems capability. There can be multiple errors. Then follow the sequence in the diagram: Select the required Calibration Interval Rear Panel switch.

At operations and ; No Remote Sense on. If oxidation is a problem use gold-plated dqtron terminals, and replace the terminals before the plating wears off. Terminators Two terminating characters are available, as programmed by code.

Not applicable for AC operation. Measui’ement imd Storage of the values of an internal resistor. Remote Sense is automaticaiiv deselected.

Full Scale value of next lower range. Use Calculations A and C if the was last calibrated by Datron. General Procedural Information 7.

It changes the DC gain of all voltage and current ranges in the same ratio, and thus performs the same function as tri mmin g the internal Master Reference voltage.