DIXEL XR100C PDF

  • August 18, 2019

Dixell technology is leading the way in electronic regulation and control in the fields of refrigeration, air conditioning and heating, and retail. Dedication to. Dixell. Installing and Operating Instructions rel /02/ – cod. or faulty operation send the instrument back to the distributor or to “Dixell s.r.l.” (see. Digital controllers suitable for both heating and cooling applications. • Built in RS for connection to Dixell’s monitoring system. • Temperature control can be .

Author: Nejin Kazirn
Country: Equatorial Guinea
Language: English (Spanish)
Genre: Photos
Published (Last): 24 January 2008
Pages: 412
PDF File Size: 17.30 Mb
ePub File Size: 11.64 Mb
ISBN: 859-5-66563-858-9
Downloads: 31093
Price: Free* [*Free Regsitration Required]
Uploader: Yobei

This temperature is sensed by the evaporator probe if fitted Sets the interval time between the start of successive defrosts Turns the decimal point on or off. If there is any risk of water getting behind the front mounting then this must be prevented by the use of a suitable gasket PELE The controller will then resume normal operation Sets the interval time between the start of successive defrosts After defrost, the temperature as it was at commencement of defrost is displayed.

Digital Thermometer XRC V – Thermometer

Do not fit a controller in a place where it will be subjected to excessive vibration. Use them in conjunction with the parameter list for a particular model Note: If set for hot gas, the compressor is kept running during defrost Sets the evaporator temperature at which the controller will terminate the defrost.

Not for thermocouple models. Output interference If the control is connected to an inductive coil e. Its aim was to provide a solution to the problem of sourcing a service replacement when there are so many different types of controller being installed as original equipment.

Setting time to 0 to disables this function Sets the period of time following a thermostat override after which the controller will go into a defrost.

Have all the required parameters now been set correctly? This parameter sets the override time during which the compressor will run continuously irrespective of the temperature.

  ECUACION DE GIBBS DONNAN PDF

If set for hot gas, the compressor fixel kept running during defrost. If the decimal point is switched on rESall parameter values expressed in degrees will be divided by 10, including the Set Point. To allow you to decide how much if any access you wish the end user to have, you can transfer any parameter or combination of parameters between the two access levels. Probe offset adjustment — thermostat Probe offset adjustment — evaporator Sets the display to read out in Celsius or Fahrenheit If a probe fault is detected the display will flash P1 and the controller will automatically cycle the compressor on and off.

Dixell parametric controllers, fan speed controllers and inverters, compressor controls, EEV drivers, sensors and monitoring systems are trusted around the world.

For more specific information on how we use cookies and to change your cookie preferences, see our Cookie Notice. Should the existing sensors need to be replaced, the Universal-R is supplied complete with 2 new PTC sensors.

It can also be used to stagger the re-start x100c multiple units following a power failure, to prevent everything trying to start at once and blowing a fuse. As a result programming takes just a few minutes using the new ‘Quick Programming’ guide. Sets the initial temperature alarm delay time on start up so avoiding unnecessary alarms while temperatures stabilize.

Only for XRC with alarm relay: H it H 30 mins.

98473 – Digital Thermometer XR100C 230V

If the existing sensors are incompatible or possibly faulty, they can be replaced by the two new PTC sensors which come supplied with the Universal-R. Dixell technology is leading the way in electronic regulation and control in the fields of refrigeration, air conditioning and heating, and retail.

Setting time to 0 to disables this function If a probe fault is detected the display will flash P1 and the controller will automatically cycle the compressor on and off. How We Use Cookies: Access all Dixell manuals. To insure all changes are updated without delay, turn the power off, then on again.

  BATLS MANUAL PDF

Sensor xixel and extension of probe cables It is important to avoid running probe cables close to power cables or other electrical equipment and cables that carry or switch heavy loads. Sets the time delay between a temperature or pressure alarm condition being sensed and the alarm being signaled during normal operation. The new version, designated v 2.

Pr1 -1c Pr1 -1 c Pr2 Min. The controller has a thermostat override facility. Adjusts the off — set of the evaporator probe Turns the decimal point on or off. Tells the controller how many stages it is controlling. Pr2 0 dPO First Defrost after start up Tells the controller whether to do an immediate defrost when the power is switched on or to wait for the normal interval time as set in parameter IdF.

Normal display is resumed once the xr00c temperature drops below this point or the time set in this parameter has expired Configures the xr100v for defrost by electrical heaters or hot gas.

Parameters in the Visible Menu can now be accessed directly. These controllers are electrical devices. Any alteration that have been made will be stored. PTC input for temperature, mA input for pressure Sets the band width above set point within which zr100c controller will switch the stages on and off.

Configures output Relay 1 to inverse or direct action. CON Spikes of up to 35 times the normal line voltage are not uncommon and will often either damage or influence any electronic control. The Universal-R can be used as a service replacement for all popular 32 x 74mm format electronic refrigeration controllers listed opposite.