Buy Metal Online – Online Metal Store – Order Large or Small Quantity ASTM B T6 Aluminum Equal Leg Structural Angle – Cut to Size Structural. Buy Metal Online – ASTM B T6 Aluminum Round Tube – Order Large or Small Quantity Online – Cut to Size Aluminum Round Tube – No Minimum. Jiangsu Haohua Industry Group as one of the leading suppliers in China to supply ASTM B T6 Aluminum Pipe etc. [Contact person:Ms chris ; Email.
C The discontinuity class limits are de? B22108 Elongation of full-section and cut-out sheet-type specimens is measured in 2 in. Any requirement not so covered is subject to negotiation between the producer and purchaser. X, and so forth A2.
The total for other elements does not include zirconium. Marking for shipment of such material shall be in accordance with Fed. NOTE 3—It is standard practice in the United States aluminum industry to b221-008 conformance to the chemical composition limits prior to further processing of ingots into wrought products.
E Other Elements—Total shall be the asrm of unspeci? Refer to Terminology B for de? F The aluminum content shall be calculated by subtracting from To determine conformance to this speci? Elongation of cut-out round specimens is measured in 43 specimen diameter.
Retest and Rejection Weight, max per Piece, lb Max Width: NOTE 4—It is difficult to obtain a reliable analysis of each of the components of clad materials using material in its? A superscript epsilon e indicates an editorial change since the last revision or reapproval.
If b221-0 chemical composition has been determined during the course of manufacture, analysis of the? Analysis shall be made for the elements for which limits are shown in this table. Tensile Properties of Material from the Producer 8. O H H up through 5. Committee B07 has identi? Tube Other Than Round Angularity: B — 05a Standard Speci?
ASTM B221-08 6061-T6 Aluminum Bar Steel Round Bars / Tubes For Stakes , Tines
Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility. B When material is found to be unacceptable, it shall be reprocessed additional precipitation heat treatment or re-solution heat treatment, stress relieving, straightening, and precipitation heat treatment, when applicable.
ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard.
The test location shall be 9 M Properties not applicable to extruded tube over 2. L Only in tube form. A designation not in con?
ASTM B221-08 PDF
The applicable level shall be as speci? NOTE 1—Throughout this speci? The cladding composition is more difficult to determine because of the relatively thin layer and because of diffusion of core elements to the cladding. Unalloyed aluminum contains a minimum of Due to the continuous nature of the process, it is not practical to keep a speci?
A number in parentheses indicates the year of last reapproval.
ASTM B PDF – $ : : National Standards Institute Documents Download Store
Specimens shall be selected at random and shall be, b221-08 possible, a minimum of 2 by 4 in. Originally approved in B The thickness of any element of a pro? Rod, Bar and Pro?
G Material in the T42 and T62 tempers is not available from the b221-0 producers. NOTE 2—For rolled or cold-? C For the purpose of determining conformance to these limits, an observed value or a calculated value obtained from analysis shall be rounded to the nearest unit in the last right-hand place of the? Materials and Manufacture 5. J Minimum yield strength for tube, If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown asstm.
Sampling shall be in accordance with Practice E However, such analysis is not required and may not cover all metallic Others elements. E These alloys are also produced in the F temper for which no tensile properties are speci? For a b221–08 having a diameter larger than can be properly mounted for polishing and examination, the portions of the cross section polished for examination may consist of an arc about 1? Other methods may be used only when no published Astk test method is available.